SciCan Statim 2000 Návod k obsluze stáhnout pdf (Strana 23)

FIGURE 9.6 - PUMPFIGURE 9.5 - CASSETTE

42 43

9.0 – REFERENCE BLOCKS

(continued)

CASSETTE DIAGNOSTICS:

If water is leaking at the drain from the cassette bay

(underside of sterilizer), then do the following:

● Remove and clean cassette seal and groove. Rein-

stall cassette seal. Run a cycle and reinspect for leak-

age. See page 10, Figure 2.6.

● Confirm that the cassette seal port holes are not dam-

aged and that they are properly aligned within the

cassette groove.

● Ensure that there is no debris or residue on outer

edges of cassette tray.

9.0 – REFERENCE BLOCKS

(continued)

Flow

ULKA VERSION PUMP

with Autoclave Software R604 and above.

ULKA Pump was introduced in conjunction

with Main PC Board Rev. 7 (Software ver-

sion R604) and was never supplied with

mesh filter installed into inlet and outlet

fittings. NOTE: Ulka Pump can be used on

Main PCB Rev. 6.4 with upgraded software

to Rev. R604 and above.

INVENSYS VERSION PUMP

with Autoclave Software R603 and older.

• Effective March 2006, all pumps were

supplied with the spring clip (grounding)

to improve water conductivity circuitry.

• In early 2006, the OEM introduced the

Reservoir Cap & Filter (RPI Part #SCK059).

• Effective June 2007, the OEM stopped

using the mesh filter (installed inlet and

outlet fittings) and offered the In-Line

Water Filter (RPI Part #SCF034) to be in-

stalled between the reservoir and pump.

• The OEM now recommends the use of

the Reservoir Cap & Filter (RPI Part

#SCK059) along with the In-Line Water

Filter on all units. The mesh filters should

be removed and the autoclave should be

upgraded to the In-Line Water Filter (Drain

Kit with Pump Filter RPI Part #SCK037).

Clean/Remove Mesh Filter

Use this clear protective tubing

to avoid water leakage onto AC

input wiring

Use this clear protective tubing

to avoid water leakage onto AC

input wiring

Spring Clip

(Ground Contact)

Over-Temp Switch

Black (Line)

To Main PCB J1-5

White (Neutral)

To Main PCB J1-6

Black (Line)

To Main PCB J1-5

White (Neutral)

To Main PCB J1-6

Cassette Lid Square Notches

(for cassette seal alignment)

BACK REAR VIEW

Injection Steam Port

Exhaust Steam Port

Located on

Probe Bracket

Steam Port

sealing

surfaces

Cassette Seal

Locating Tabs

and Port Holes

Cassette Lid

Port Holes

Lid

Venturi Plate

Tray

RPI Cassette Seal Part Number

is located in this approximate

location (inside Seal Channel)

}

● Verify that outer edges of cassette tray are straight

(not nicked, dented, or damaged).

● Check the integrity of the hinge.

● Check the cassette tray and lid for warpage.

Straighten or replace as necessary.

● Inspect and clean steam ports on probe bracket. If

you observe excess debris that is not easily removed,

or if the steam ports appear to be worn or damaged,

remove probe bracket for proper evaluation. Replace

probe bracket if necessary. See page 13, Figure

2.10B.

Clean/Remove

Mesh Filter

Check these

areas for debris

build up

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 29

Komentáře k této Příručce

Žádné komentáře

SciCan Statim 2000 Návod k obsluze Strana 23

Komentáře k této Příručce